GE appliance repair in Ottawa and Gatineau

GE Appliance Repair Service

Fast, local repairs across Ottawa and Gatineau. Book online or give us a call, and we'll have your GE working again.

  • Any age or model of appliance
  • Only quality, manufacturer-recommended parts
  • Certified and insured technicians

Troubleshooting

Common GE Faults We Fix

Tap an appliance to see the problems we see most, what usually causes them, and what you can safely try before you call.

GE Fridge Repair

Not cooling, leaks, ice-maker faults or loud fans.

GE fridges use TwinChill evaporators to manage the fridge and freezer separately, with Turbo Cool and Turbo Freeze for fast recovery and advanced water filtration.

Common faults

  • Fridge warm while the freezer stays cold
  • Water pooling under the crisper drawers
  • The dispenser or autofill pitcher not working
  • Ice maker frozen over or not dropping ice
  • Fan noise that grows louder over time

What usually causes it

  • A frosted-over evaporator coil
  • A blocked or frozen defrost drain
  • A door seal that no longer closes tightly
  • An iced-up ice maker that needs a reset
  • A clogged or overdue water filter affecting the dispenser

What you can try yourself

  • Check the doors seal properly and nothing holds them open
  • Clear internal vents and keep the fridge off the wall
  • Replace the water filter if it is overdue
  • Reset the ice maker with its feeler arm or reset button

Leave the sealed system and wiring to a technician. If it still will not cool, we can diagnose it on site and usually fix it in one visit.

GE Washer Repair

Won't drain or spin, error codes, leaks or shaking.

GE washers include SmartDispense and Deep Fill on many models, with dynamic balancing to steady the spin. Faults often show as a code or a flashing light.

Common faults

  • Will not drain or spin
  • Long cycles or a cycle that will not advance
  • Leaks around the door or dispenser
  • A drum that bangs or walks on spin
  • A musty smell in front-load models

What usually causes it

  • A clogged drain pump or hose
  • An unbalanced or overloaded drum
  • Inlet hoses or taps restricting the water
  • A door seal holding debris in front-load models
  • A lid switch or door lock not registering

What you can try yourself

  • Clean the drain pump filter if your model has an access panel
  • Level the machine and balance the load
  • Check the inlet hoses and taps are open and unkinked
  • Wipe the door seal and run a clean cycle for smells

Leave the motor, transmission and control board to us. If a code keeps returning, we can find the cause and repair it.

GE Dryer Repair

No heat, long dry times, won't start or noisy.

GE dryers use HE Sensor Dry and Damp Alert to stop when clothes are ready, and the DuraDrum is designed to be gentle on fabrics.

Common faults

  • No heat at all
  • Very long drying times
  • Will not start or stops partway
  • A drum that squeals or thumps
  • Clothes still damp when the cycle ends

What usually causes it

  • A lint-clogged filter or vent
  • A blocked or crushed exhaust duct
  • Moisture sensor bars coated in residue
  • A worn drum roller, belt or idler
  • A thermal fuse tripped by restricted airflow

What you can try yourself

  • Clean the lint filter before every load
  • Clear the vent and exhaust duct
  • Wipe the moisture-sensor bars inside the drum
  • Check the exhaust flap outside opens freely

Leave the heating element, motor and wiring to a technician, and stop using a gas dryer if you suspect a gas fault. If it still will not heat or dry, we can sort it out.

GE Dishwasher Repair

Won't drain, leaks, error lights or poor cleaning.

GE dishwashers use AutoSense cycles and Dry Boost, with bottle jets and a Piranha hard-food disposer to handle heavier loads.

Common faults

  • Standing water that will not drain
  • Leaks onto the floor
  • Dishes coming out dirty or still wet
  • Flashing lights or a beeping code
  • A door that will not latch

What usually causes it

  • A clogged filter or drain hose
  • Spray arms blocked with food or hard-water scale
  • A drain solenoid or check valve stuck
  • A door latch or seal problem
  • A supply issue starving it of water

What you can try yourself

  • Rinse the filter at the bottom of the tub
  • Clear the spray-arm holes of debris and scale
  • Check the drain hose is not kinked and the sink drain is clear
  • Run a cleaning cycle to cut grease and limescale

Leave the pump, drain valve and control board to us. If it still will not drain or clean, we can find the fault and fix it in one visit.

GE Stove Repair

Burner or element won't heat, sparking or control faults.

GE cooktops come in gas, radiant and induction, with a Power Boil burner on gas models and precise, fast heating on induction.

Common faults

  • A gas burner that will not light or keeps clicking
  • An element that will not heat or heats unevenly
  • An induction zone that will not recognise a pan or cuts out
  • Cracked ceramic glass
  • Unresponsive controls or knobs

What usually causes it

  • A dirty or wet igniter and burner cap on gas models
  • A failed element, switch or infinite control on radiant models
  • Cookware that is not induction-compatible, or a zone protecting itself from overheating
  • Controls confused by spills or moisture

What you can try yourself

  • On gas, dry the burner caps, seat them correctly and clean the ports
  • On induction, try a pan you know is induction-ready
  • Keep the glass clean and dry
  • Wipe controls and knobs to clear spills

Do not attempt gas-line, wiring or internal repairs yourself; leave these to a qualified technician. If the burner or element still will not behave, we can diagnose and repair it.

GE Oven Repair

Won't heat, wrong temperature, door or control faults.

GE ovens use True European Convection with Precise Air for even results, plus No-Preheat Air Fry and a temperature probe on many models.

Common faults

  • Will not heat or is slow to reach temperature
  • Baking that is uneven or off from the set temperature
  • A convection fan that is noisy or not running
  • A door that will not close or lock
  • A panel that freezes or throws a code

What usually causes it

  • A failed bake or convection element
  • A temperature sensor reading wrong so the oven never settles
  • A worn door seal or hinge letting heat escape
  • Control faults after a power surge or an overheated self-clean cycle

What you can try yourself

  • Check the door closes fully and the seal is intact
  • Use an oven thermometer to see how far off the temperature is
  • Reset the oven at the breaker if the panel has locked up
  • Use a Steam Clean cycle for light jobs to avoid overheating the panel

Leave the element wiring, sensor and control board to a technician. If the oven still will not hold temperature, we can measure it, find the fault and repair it.

Tried these and still stuck? (613) 909-3442 or book a repair.

Portage Appliance Repair — Booking form block preview

Let's get it fixed

Book online or give us a call. The visit and diagnosis are free when you book the repair with us.

Hours

Open every day, 7am to 11pm

Call us

(613) 909-3442